A
ALTIUS CMFacade · Roofing · Construction Mgmt
ROOFING

Roof Drains, Ponding Water and Parapet Flashing: Where Commercial Roofs Fail

Published November 8, 2026

Schematic cross-section of a low-slope roof showing coping, counterflashing, parapet wall, roof drain, scupper and a low-lying area where water pondsA generic cross-section, not to scale. A roof deck with a membrane runs left to right. A roof drain with a strainer sits at the left, a low-lying area where water ponds is in the middle, and a parapet wall rises at the right with coping on top, counterflashing on its face and a scupper opening through it near the roof surface.123456Schematic, not to scale1CopingBC 1503.32Counterflashing3Parapet wall4Roof drain5ScupperBC 1503.4.26Low-lying areaPonding
Generic cross-section, schematic and not to scale. 1 Coping, BC 1503.3. 2 Counterflashing. 3 Parapet wall. 4 Roof drain. 5 Scupper, BC 1503.4.2. 6 Low-lying area where ponding collects. These are the places the post covers: where water collects, where it gets trapped when a drain backs up, and where the roof runs into a wall.

Why do commercial roofs fail at drains, ponds and parapets?

Commercial roofs fail where water collects, where water gets trapped when a drain backs up, and where the roof runs into a wall.

The NYC Building Code deals with all three. So do manufacturer warranty documents, with requirements and exclusions of their own.

What follows sticks to the code, NRCA, and manufacturer documents. It also points to Altius CM project records with drain and flashing work.

What counts as ponding water?

NRCA’s glossary defines ponding as “the excessive accumulation of water at low-lying areas on a roof that remains more than 48 hours after precipitation under conditions conducive to drying.”

Carlisle’s care and maintenance guide, attached to its sample Golden Seal warranty, uses a similar benchmark. It states that “ponded water should evaporate within 48 to 72 hours after a rainfall” and that debris can inhibit drainage.

Standing water is both a design problem and a warranty problem. Johns Manville’s guarantee overview lists “damage due to improper drainage (ponding water)” as not covered, with an exception for TPO and PVC membranes available with prior approval. Roof warranties explained covers the rest of the exclusions.

How much does water on a roof weigh?

BC 1611.1 sets the design rain load as R = 5.2 (ds + dh), in pounds per square foot with depths in inches.

Here, ds is the depth of water up to the inlet of the secondary drain when the primary system is blocked. dh is the added head above that inlet at design flow. Each inch of depth is 5.2 psf, so six inches is 31.2 psf.

BC 1611.2 also requires susceptible bays to be evaluated for ponding instability under ASCE 7 section 8.4. BC 1611.3 requires roofs with flow-control hardware to have a secondary drainage system at a higher elevation.

What does NYC require for drains and scuppers?

Chapter 15 sends drainage design to Chapter 11 of the NYC Plumbing Code and adds these requirements:

  • Secondary drains (BC 1503.4.1). Where roof drains are required, secondary drains or scuppers are required where the perimeter construction extends above the roof so water would be trapped if the primary drains back up.
  • Scuppers (BC 1503.4.2). Sized so ponding depth cannot exceed what the roof was designed for under BC 1611.1, with no opening dimension under 4 inches, and without counting flow through the primary system.
  • Reroofs (BC 1511.1). A replacement need not add secondary drains if the roof has positive drainage, but existing required secondary systems cannot be removed unless replaced with compliant ones. BC 1511.1.1 requires positive drainage on every reroof.
  • Drawings. DOB’s plan examination guidelines require roof plans to show roof drains and roof pitch, and the parapet with its height.

At 1251 Avenue of the Americas, Altius CM’s scope on a 28,000 sq ft roof included refurbishing the existing roof drains and installing new cast iron strainers and clamping rings, alongside the reinforced fluid-applied assembly.

What does the code say about parapet flashing?

BC 1503.2 requires flashing “so as to prevent moisture entering the wall and roof through joints in copings, through moisture-permeable materials and at intersections with parapet walls.”

BC 1503.2.1 lists wall and roof intersections, changes of slope or direction, and roof openings, and sets a minimum of 0.019 inch for metal flashing. BC 1503.3 says parapet walls shall be coped with noncombustible, weatherproof materials no narrower than the parapet is thick.

Reroof work has its own rules here. BC 1511.6 requires flashings to be reconstructed per the manufacturer’s instructions. BC 1511.5 bars reinstalling existing metal edgings, counterflashings and drain outlets that are rusted, damaged or deteriorated. In plain terms, rusted or damaged counterflashing gets replaced, not tied into.

At 111 Hudson Street the scope includes counterflashing at parapet walls with a 150 LF flashing allowance, and at 311 Franklin Avenue the team did liquid flashing and metal work at roof details.

Why do warranties treat these areas differently?

The exclusions are specific.

Johns Manville excludes “damage resulting from infiltration of moisture in, through or around walls, copings, penetrations, building structure or underlying or surrounding areas.” Carlisle’s warranty options sell sheet says metal edge is not covered under its Golden Seal Total Roofing System warranty and is included only in its Edge-to-Edge warranty. Its maintenance guide also notes that wind damage often begins at the perimeter.

If the parapet wall or coping leaks, the roof guarantee may not respond.

What about parapet inspections?

This is separate from the roof.

1 RCNY §103-15 requires an annual observation of parapets on buildings with parapets fronting the public right-of-way, regardless of height, starting January 1, 2024. Detached 1- or 2-family homes and buildings with a fence or barrier blocking access to the exterior wall are excluded.

Unsafe conditions must be corrected within 90 days of notification to DOB. Details are in our parapet observation guide, and the repair work is covered under parapet repair and replacement.

What should an owner check on a roof walk?

  1. Standing water in the same low spots more than 48 hours after rain.
  2. Strainers, clamping rings and leaders: present, clear, and not rusted through.
  3. Whether secondary drains or scuppers exist at each parapeted area.
  4. Coping joints, counterflashing and metal edge: loose, open or rusted.
  5. A record, with dates and photos, of what you found.

Start the repair-or-replace decision with replace vs recover vs restore, and see roof repair and replacement and the roofing hub.

Sources

Last verified: November 8, 2026. This is general information, not legal advice or an engineering opinion; have a registered design professional evaluate drainage and loads on your roof.

Frequently asked questions

What counts as ponding water on a commercial roof?

NRCA's glossary defines ponding as the excessive accumulation of water at low-lying areas on a roof that remains more than 48 hours after precipitation under conditions conducive to drying. Carlisle's care and maintenance guide states a similar benchmark, that ponded water should evaporate within 48 to 72 hours after a rainfall.

How much weight does water on a roof add?

NYC Building Code BC 1611.1 sets the design rain load as R = 5.2 times the depth of water in inches, where depth is the static head up to the secondary drain inlet with the primary drains blocked, plus the hydraulic head above that inlet. At that factor, each inch of water adds 5.2 pounds per square foot, so six inches is 31.2 pounds per square foot. BC 1611.2 also requires susceptible roof bays to be checked for ponding instability under ASCE 7 section 8.4.

Does the NYC Building Code require secondary roof drains?

Where roof drains are required, BC 1503.4.1 requires secondary (emergency overflow) drains or scuppers where the roof perimeter extends above the roof so that water would be trapped if the primary drains back up. Scupper openings may not be smaller than 4 inches in any dimension, and they are sized without counting flow through the primary system (BC 1503.4.2). A reroof does not have to add them if it provides positive drainage, but BC 1511.1 says existing required secondary drains cannot be removed unless replaced with compliant ones.

What does the building code say about parapet flashing and coping?

BC 1503.2 requires flashing that prevents moisture from entering the wall and roof through joints in copings, through moisture-permeable materials and at intersections with parapet walls and other penetrations. BC 1503.2.1 puts flashing at wall and roof intersections and wherever slope or direction changes, and metal flashing must be at least 0.019 inch thick (No. 26 galvanized sheet). BC 1503.3 requires parapet walls to be coped with noncombustible, weatherproof material at least as wide as the parapet is thick.

Do roof warranties cover ponding water and parapet leaks?

Often not. Johns Manville's guarantee overview excludes damage due to improper drainage (ponding water), except that TPO and PVC membranes may be covered with prior approval, and it excludes moisture infiltration in, through or around walls, copings and penetrations. Carlisle's Golden Seal warranty does not include metal edging, which only its Edge-to-Edge option covers. Read the exclusions before relying on a warranty for these conditions.

Does NYC require inspection of parapets?

Yes. 1 RCNY §103-15 requires an annual observation, starting January 1, 2024, of parapets on buildings with parapets fronting the public right-of-way, regardless of height, except detached 1- or 2-family homes and buildings with a fence or barrier that blocks access to the exterior wall. Unsafe conditions found must be corrected within 90 days of notification to DOB. Our parapet guide covers who may perform the observation and what the report must contain.

Need roof work scoped?

Contact Altius CM